Leading wood drying equipment from China, economical and reliable performance.
PARLICULAR DETAILS
1. BEARING STRUCTURE
The structure of the kiln is made completely of special aluminum alloy AW6063. All the beams, profiles, and roof holding structure as well as wind-bracing have high resistance to corrosion, which are of I, U, L & C .
The complete structure is self-supporting and is mounted on to a base concrete foundation using stainless- steel heavy-duty dowels.
The connecting materials, bolts, nuts &washer are made of stainless steel. The offered bearing structure can bear stress of 150kg/m2 of snow load and wind load of 120km/h.
2. KILN CASSETES SHEETING AND INSULATION SYSTEM
The heat insulation system is made of aluminum cassette-panels of alloy with high density non-flammable rock wool thermal insulation of 120mm thickness, the density of rock wool is 55kg/m3, which is higher than that of fiberglass. There is a slope on the roof, avoiding accumulation of rain or snow on the roof. The kiln wall is externally and internally faced with corrugate embossed aluminum sheets with a granulated finish of 1.1 mm. The Cassettes themselves are specially mounted with the supported of aluminum plate between columns of bearing structure. High-temperature caulking between cassettes protects the walls from heat transfer. The caulking is applied at any cassettes joints.
The thermal constant of the jacket penetrability is k=0.45w/m-2.k-1. This is due to the particular construction characteristics of the walls. They are completely fire resistant; they do not absorb moisture, guaranteeing constant operation.
3. KILN DOOR
The lifting –sliding sturdy aluminum door structure profile. The special groove where the strong rubber seal is installed provides optimum tightening alongside the doorframe. The kiln door wall is of the same construction as the kiln and roof walls using rock wool insulation of 120mm.The closing system is equipped with adjustable counterparts which enable the precise adhesion of the door to the kiln structure. The bottom mullions feature nylon rollers on heavy duty
stainless pins
4. KILN DOOR CARRIER AND LIFTING DEVICE
The TECH I’ beams monorail carriage design realizes unrestricted movement of the door which hangs vertically in its raised position. Carriage wheels are sealed ball bearing to in any weather conditions.
5. INSPECTION DOOR
The inspection door is included and is of opening 1500×600 mm
with rock wool insulation of 120mm.
It is equipped with a safety handle, easy to open and close.
The inspection door will be placed in rear wall.
6. FALSE CEILING
The chamber is divided by aluminum intermediate ceiling into a technology section where all the technical elements are located and a drying section where the timber to be dried is placed. The intermediate ceiling is mounted on the lower part of the chamber beams and is made of corrugated profile sheets of thickness1.1 mm ensuring the smooth air flow.
7 FANS & MOTORS
The air ventilation is provided by reversible medium pressure fans with high performance level installed in each chamber above false ceiling of the chamber. The fans can perform with the same efficiency and capacity in both direction and at any revolution rate. Each fan has 6 aluminum swinging blades with perfectly symmetrical shape. The aluminum fan φ800 mm impellers are fixed directly on to the shaft of the specially designed motors. The motors are tropically insulated to resist high temperature (IP55) and to work without any problems in environments reaching 100% of moisture content
8 HEATING ELEMENTS
The heating elements use aluminum fin built on stainless steel pipe. Heat exchanger coils are located vertically overhead. All the piping from collectors for the heat exchanger coils up to flanges out of kilns are made in stainless steel. The heat output is designed for the highest demand.
9. THE AIR EXCHANG SYSTEM
The ventilation and suction system of vents are made of aluminum material. Vents make use of pressure and vacuum zones generated inside the chamber which avoids the use of additional fans. The whole system of vents works simultaneously. In this offer the chimney are provided in the chamber ceiling. The vents are positive opening and closing.
10. ELECTRIC BOARD
The board is the modular panel meeting the international standards relevant to protection class IP55. The operating drying components are placed in the electric board. (Switches, relays, fusing etc.)
11. AUTOMATIC CONTROL OF THE DRYING PROCESS HOLZMEISTER M800B (DELPHI)
Every unit is equipped with:
6 pcs of probes to detect the wood moisture
2 pcs of EMC stations/ front and back / For climate controlling
It is a LCD based automatic kiln controller. The kiln dryer controller DELPHI is based on the most advanced electronic technology today available and includes all the best solutions that LOGICA H&S has developed in over ten years of experience in timber drying control systems.
The new user interface, based on a LCD graphic display having a very good readability, allows an easy set-up also to not skilled users, because all setting are made through self-explaining menu and the access to most advanced menus, divided from the ones most commonly used.
Friday, June 17, 2011
ATC woodworking machine with vacuum table
woodworking machine
1.Japan YASKAWA servo motor
2.Tool magazine capacity of 8tools
3.Long service time
4.CE,FDA
RJ1325 woodworking machine with vacuum table
Advantage Features:
1.Adopt domestic water cooling spindle of big power(option: Italy HSD 8KW air cooling spindle)
2.high accuracy, long service time, steady movement and good starting performance, great torque, fulfilling the advantage of working with fast speed and low noise.
3.Japan YASKAWA servo motor ensures machine to run with fast speed and low noise
4.unique auto tool changer system can change tools alternatively, tool sensor to compensate the tolerance of tool length
5.tool magazine capacity of 8tools, changing tools only takes 8 seconds
Technical Parameters:
Working area
1300*2500mm
Max moving speed
70000mm/min
Max engraving Speed
40000mm/min
Reposition accuracy
0.025mm
Working dictate
G code
Spindle
8.0kw HSD Italy
Spindle speed
3000-24000rpm
Collect
ER32
Transmission
X,Y Rack Gear Z Ball screw
X,Y,Z guide rail
Linear square rai
Operation system
SYNTEC control system
1.Japan YASKAWA servo motor
2.Tool magazine capacity of 8tools
3.Long service time
4.CE,FDA
RJ1325 woodworking machine with vacuum table
Advantage Features:
1.Adopt domestic water cooling spindle of big power(option: Italy HSD 8KW air cooling spindle)
2.high accuracy, long service time, steady movement and good starting performance, great torque, fulfilling the advantage of working with fast speed and low noise.
3.Japan YASKAWA servo motor ensures machine to run with fast speed and low noise
4.unique auto tool changer system can change tools alternatively, tool sensor to compensate the tolerance of tool length
5.tool magazine capacity of 8tools, changing tools only takes 8 seconds
Technical Parameters:
Working area
1300*2500mm
Max moving speed
70000mm/min
Max engraving Speed
40000mm/min
Reposition accuracy
0.025mm
Working dictate
G code
Spindle
8.0kw HSD Italy
Spindle speed
3000-24000rpm
Collect
ER32
Transmission
X,Y Rack Gear Z Ball screw
X,Y,Z guide rail
Linear square rai
Operation system
SYNTEC control system
Wood drying kiln
Leading wood drying equipment from China, economical and reliable performance.
Suitable for drying both hardwood and softwood.
PARLICULAR DETAILS
1. BEARING STRUCTURE
The structure of the kiln is made completely of special aluminum alloy AW6063. All the beams, profiles, and roof holding structure as well as wind-bracing have high resistance to corrosion, which are of I, U, L & C .
The complete structure is self-supporting and is mounted on to a base concrete foundation using stainless- steel heavy-duty dowels.
The connecting materials, bolts, nuts &washer are made of stainless steel. The offered bearing structure can bear stress of 150kg/m2 of snow load and wind load of 120km/h.
2. KILN CASSETES SHEETING AND INSULATION SYSTEM
The heat insulation system is made of aluminum cassette-panels of alloy with high density non-flammable rock wool thermal insulation of 120mm thickness, the density of rock wool is 55kg/m3, which is higher than that of fiberglass. There is a slope on the roof, avoiding accumulation of rain or snow on the roof. The kiln wall is externally and internally faced with corrugate embossed aluminum sheets with a granulated finish of 1.1 mm. The Cassettes themselves are specially mounted with the supported of aluminum plate between columns of bearing structure. High-temperature caulking between cassettes protects the walls from heat transfer. The caulking is applied at any cassettes joints.
The thermal constant of the jacket penetrability is k=0.45w/m-2.k-1. This is due to the particular construction characteristics of the walls. They are completely fire resistant; they do not absorb moisture, guaranteeing constant operation.
3. KILN DOOR
The lifting –sliding sturdy aluminum door structure profile. The special groove where the strong rubber seal is installed provides optimum tightening alongside the doorframe. The kiln door wall is of the same construction as the kiln and roof walls using rock wool insulation of 120mm.The closing system is equipped with adjustable counterparts which enable the precise adhesion of the door to the kiln structure. The bottom mullions feature nylon rollers on heavy duty
stainless pins
4. KILN DOOR CARRIER AND LIFTING DEVICE
The TECH I’ beams monorail carriage design realizes unrestricted movement of the door which hangs vertically in its raised position. Carriage wheels are sealed ball bearing to in any weather conditions.
5. INSPECTION DOOR
The inspection door is included and is of opening 1500×600 mm
with rock wool insulation of 120mm.
It is equipped with a safety handle, easy to open and close.
The inspection door will be placed in rear wall.
6. FALSE CEILING
The chamber is divided by aluminum intermediate ceiling into a technology section where all the technical elements are located and a drying section where the timber to be dried is placed. The intermediate ceiling is mounted on the lower part of the chamber beams and is made of corrugated profile sheets of thickness1.1 mm ensuring the smooth air flow.
7 FANS & MOTORS
The air ventilation is provided by reversible medium pressure fans with high performance level installed in each chamber above false ceiling of the chamber. The fans can perform with the same efficiency and capacity in both direction and at any revolution rate. Each fan has 6 aluminum swinging blades with perfectly symmetrical shape. The aluminum fan φ800 mm impellers are fixed directly on to the shaft of the specially designed motors. The motors are tropically insulated to resist high temperature (IP55) and to work without any problems in environments reaching 100% of moisture content
8 HEATING ELEMENTS
The heating elements use aluminum fin built on stainless steel pipe. Heat exchanger coils are located vertically overhead. All the piping from collectors for the heat exchanger coils up to flanges out of kilns are made in stainless steel. The heat output is designed for the highest demand.
9. THE AIR EXCHANG SYSTEM
The ventilation and suction system of vents are made of aluminum material. Vents make use of pressure and vacuum zones generated inside the chamber which avoids the use of additional fans. The whole system of vents works simultaneously. In this offer the chimney are provided in the chamber ceiling. The vents are positive opening and closing.
10. ELECTRIC BOARD
The board is the modular panel meeting the international standards relevant to protection class IP55. The operating drying components are placed in the electric board. (Switches, relays, fusing etc.)
11. AUTOMATIC CONTROL OF THE DRYING PROCESS HOLZMEISTER M800B (DELPHI)
Every unit is equipped with:
6 pcs of probes to detect the wood moisture
2 pcs of EMC stations/ front and back / For climate controlling
It is a LCD based automatic kiln controller. The kiln dryer controller DELPHI is based on the most advanced electronic technology today available and includes all the best solutions that LOGICA H&S has developed in over ten years of experience in timber drying control systems.
The new user interface, based on a LCD graphic display having a very good readability, allows an easy set-up also to not skilled users, because all setting are made through self-explaining menu and the access to most advanced menus, divided from the ones most commonly used.
Suitable for drying both hardwood and softwood.
PARLICULAR DETAILS
1. BEARING STRUCTURE
The structure of the kiln is made completely of special aluminum alloy AW6063. All the beams, profiles, and roof holding structure as well as wind-bracing have high resistance to corrosion, which are of I, U, L & C .
The complete structure is self-supporting and is mounted on to a base concrete foundation using stainless- steel heavy-duty dowels.
The connecting materials, bolts, nuts &washer are made of stainless steel. The offered bearing structure can bear stress of 150kg/m2 of snow load and wind load of 120km/h.
2. KILN CASSETES SHEETING AND INSULATION SYSTEM
The heat insulation system is made of aluminum cassette-panels of alloy with high density non-flammable rock wool thermal insulation of 120mm thickness, the density of rock wool is 55kg/m3, which is higher than that of fiberglass. There is a slope on the roof, avoiding accumulation of rain or snow on the roof. The kiln wall is externally and internally faced with corrugate embossed aluminum sheets with a granulated finish of 1.1 mm. The Cassettes themselves are specially mounted with the supported of aluminum plate between columns of bearing structure. High-temperature caulking between cassettes protects the walls from heat transfer. The caulking is applied at any cassettes joints.
The thermal constant of the jacket penetrability is k=0.45w/m-2.k-1. This is due to the particular construction characteristics of the walls. They are completely fire resistant; they do not absorb moisture, guaranteeing constant operation.
3. KILN DOOR
The lifting –sliding sturdy aluminum door structure profile. The special groove where the strong rubber seal is installed provides optimum tightening alongside the doorframe. The kiln door wall is of the same construction as the kiln and roof walls using rock wool insulation of 120mm.The closing system is equipped with adjustable counterparts which enable the precise adhesion of the door to the kiln structure. The bottom mullions feature nylon rollers on heavy duty
stainless pins
4. KILN DOOR CARRIER AND LIFTING DEVICE
The TECH I’ beams monorail carriage design realizes unrestricted movement of the door which hangs vertically in its raised position. Carriage wheels are sealed ball bearing to in any weather conditions.
5. INSPECTION DOOR
The inspection door is included and is of opening 1500×600 mm
with rock wool insulation of 120mm.
It is equipped with a safety handle, easy to open and close.
The inspection door will be placed in rear wall.
6. FALSE CEILING
The chamber is divided by aluminum intermediate ceiling into a technology section where all the technical elements are located and a drying section where the timber to be dried is placed. The intermediate ceiling is mounted on the lower part of the chamber beams and is made of corrugated profile sheets of thickness1.1 mm ensuring the smooth air flow.
7 FANS & MOTORS
The air ventilation is provided by reversible medium pressure fans with high performance level installed in each chamber above false ceiling of the chamber. The fans can perform with the same efficiency and capacity in both direction and at any revolution rate. Each fan has 6 aluminum swinging blades with perfectly symmetrical shape. The aluminum fan φ800 mm impellers are fixed directly on to the shaft of the specially designed motors. The motors are tropically insulated to resist high temperature (IP55) and to work without any problems in environments reaching 100% of moisture content
8 HEATING ELEMENTS
The heating elements use aluminum fin built on stainless steel pipe. Heat exchanger coils are located vertically overhead. All the piping from collectors for the heat exchanger coils up to flanges out of kilns are made in stainless steel. The heat output is designed for the highest demand.
9. THE AIR EXCHANG SYSTEM
The ventilation and suction system of vents are made of aluminum material. Vents make use of pressure and vacuum zones generated inside the chamber which avoids the use of additional fans. The whole system of vents works simultaneously. In this offer the chimney are provided in the chamber ceiling. The vents are positive opening and closing.
10. ELECTRIC BOARD
The board is the modular panel meeting the international standards relevant to protection class IP55. The operating drying components are placed in the electric board. (Switches, relays, fusing etc.)
11. AUTOMATIC CONTROL OF THE DRYING PROCESS HOLZMEISTER M800B (DELPHI)
Every unit is equipped with:
6 pcs of probes to detect the wood moisture
2 pcs of EMC stations/ front and back / For climate controlling
It is a LCD based automatic kiln controller. The kiln dryer controller DELPHI is based on the most advanced electronic technology today available and includes all the best solutions that LOGICA H&S has developed in over ten years of experience in timber drying control systems.
The new user interface, based on a LCD graphic display having a very good readability, allows an easy set-up also to not skilled users, because all setting are made through self-explaining menu and the access to most advanced menus, divided from the ones most commonly used.
Wood edge banding machineMD516B01 with the gluing and fine trimming machine
1>Manual
2>High credit
3>Eazy to operate
4>Good quality
5>Good after-sales service
Features
1. Woodworking edge banding machine
2. High precision and efficiency
3. CE;ISO9001
4. Manual
5. Function: Edge Banding
1. MD516A Woodworking Edge Banding Machine
2. Adapted to the linear sealing of PVC, Melamine and veneer etc.
3. Using imported quality engines and electric components.
4. Serialized products, a wide range of selection by customers
5. High precision and efficiency
6. Main function: a. Gluing
d: Fine finishing
f: Scraping
g: Polishing
7. A leading edge banding machine professional manufacturer in China.
Main Te
chnical Data
Model
MD516B
Motor Power
1.5kw
Min working radius
20mm
Feed Speed
12—20m/min
Edge width
15—50mm
Edge banding tape thickness
0.4—3mm
Panel Width
≥80mm
Working Air Pressure
6kg
Weight
280kg
Configuration Form
Pre-milling
×
Gluing
√
End Trimming
×
Rough Trimming
×
Fine Trimming
√
Profiling Unit
×
Scraping
×
Buffing
√
Grooving
×
2>High credit
3>Eazy to operate
4>Good quality
5>Good after-sales service
Features
1. Woodworking edge banding machine
2. High precision and efficiency
3. CE;ISO9001
4. Manual
5. Function: Edge Banding
1. MD516A Woodworking Edge Banding Machine
2. Adapted to the linear sealing of PVC, Melamine and veneer etc.
3. Using imported quality engines and electric components.
4. Serialized products, a wide range of selection by customers
5. High precision and efficiency
6. Main function: a. Gluing
d: Fine finishing
f: Scraping
g: Polishing
7. A leading edge banding machine professional manufacturer in China.
Main Te
chnical Data
Model
MD516B
Motor Power
1.5kw
Min working radius
20mm
Feed Speed
12—20m/min
Edge width
15—50mm
Edge banding tape thickness
0.4—3mm
Panel Width
≥80mm
Working Air Pressure
6kg
Weight
280kg
Configuration Form
Pre-milling
×
Gluing
√
End Trimming
×
Rough Trimming
×
Fine Trimming
√
Profiling Unit
×
Scraping
×
Buffing
√
Grooving
×
Wood effect machine
Wood effect machine
1.Machine capacity: 800-1000 tons/year
2.Desiel/electrical/coal/gas heating
3.Heavy dutiy baking chamber
Wood effect machine
Put the sheet metal in the table, and lay the transfer paper on the sheet metal. A pump will create a vacuum, which makes a perfect adherence of the transfer paper on the surface of the sheet metal.
The table will be pushed in to the infiltration oven manually / automatically after the vacuum process is finished, Where it will stay for 2~3 minutes till the temperature reach up to 180. This will make it possible for the pigment inks transfer from the paper into the coating layer. The transfer process is finished as the table comes out of the oven with an excellent quality result and a remarkable reduction of the production cost.
Specification:
1.Machine capacity: 800-1000 tons/year
2.Desiel/electrical/coal/gas heating
3.Heavy dutiy baking chamber
4.Key parts imported from Italy
5.Operator friendly working table
6.Cost effective solution for every plant
1.Machine capacity: 800-1000 tons/year
2.Desiel/electrical/coal/gas heating
3.Heavy dutiy baking chamber
Wood effect machine
Put the sheet metal in the table, and lay the transfer paper on the sheet metal. A pump will create a vacuum, which makes a perfect adherence of the transfer paper on the surface of the sheet metal.
The table will be pushed in to the infiltration oven manually / automatically after the vacuum process is finished, Where it will stay for 2~3 minutes till the temperature reach up to 180. This will make it possible for the pigment inks transfer from the paper into the coating layer. The transfer process is finished as the table comes out of the oven with an excellent quality result and a remarkable reduction of the production cost.
Specification:
1.Machine capacity: 800-1000 tons/year
2.Desiel/electrical/coal/gas heating
3.Heavy dutiy baking chamber
4.Key parts imported from Italy
5.Operator friendly working table
6.Cost effective solution for every plant
Wood engraving CNC Router XYZ1325
XYZ1325 CNC Router
1 Italy HSD Air-cooled spindle
2 HIWIN rail guide
3 Vacuum Table/Dust collector/Automatic-mist spray
XYZ 1325 Wood Working CNC Router
Description
Parameter
X, Y, Z working area
1300 X 2500 X 200 mm
X, Y Movement
Rack and Pinion transmission, Linear Square orbit (Taiwan Hiwin).
Z - Movement
Imported ball screw made in Germany Linear Square orbit (Taiwan HIWIN)
Resolution Working Accuracy Reposition Accuracy
0.01 mm
0.05 mm
Machine Bed Structure
Welded Steel tube structure
Bed Type
T Slot + Vacuum
Max. idling speed
50 m/min
Spindle Type
3.0, 6kw air cooled HSD Italy
Spindle speed
0-24000 rpm (0-18000 rpm for HSD spindle)
Working voltage
Three Phase 380V/50Hz
Inverter
Delta Taiwan
Drive Motors
Stepper
Max. Power (without spindle)
1850 Watts
Max. Working Speed
25m/min
Command
G code, HPGL, U00, mmg, plt
Operating system
DSP
Interface
USB
Diameter of cutter
¦Õ3.175-¦Õ12.7
Dust collector (complete)
Yes
Work-holding
T Slot + By suction (vacuum)
Features:
1 The machine is welded with square steel tube, which has excellent stability and long life.
2 X and Y axis adopt rack and pinion transmission.Dust prooof structure on X axis.
3 Z axis adopts ball screw transimission.
4 Lubrication system on rails.
5 Software compatability: CAD/DAM design software eg. Type3/CorelDraw/Artcam/Castmate,etc. It can run on Windows XP/2000,32bits.
6 It has function of recarving/resuming after tool breakage, temporary pause and power failure. It has Memery to capture processing point. (DSP can capture 6 this break point when the tool or blade is broken or insituation of postponement, or of power failure.(only DSP can resume from power failure)
7 It has intelligent protection for working table to prevent damage. Our solution is to put a 5 mm MDF board on top of T-slot&vacuum table.
8 It has function of forecasting processing time.
9 It adopts advanced DSP system, with USB interface, for convenient ooperation. The engraver is capable of working completely off-line without any computer resources. Flas Memery 128 MB.
10 It has an independent control box.
11 Vacuum table with enough vacuum zones, which can hold different size of material. It is also very convenient to fix the material by clamp.
Function:
This machine is widely used in many industries such as: furnature, decoration, wooden doors, stone,metal....It is suitable to process various wooden products, nameplate, handicraft, graveston,
embossing, advertisement signboards, MDF, hard plastic, archaized furniture, arcrylic cutting, curved surface musical instrument, sucktion mould making, and other metallic or nonmetallic material....
1 Italy HSD Air-cooled spindle
2 HIWIN rail guide
3 Vacuum Table/Dust collector/Automatic-mist spray
XYZ 1325 Wood Working CNC Router
Description
Parameter
X, Y, Z working area
1300 X 2500 X 200 mm
X, Y Movement
Rack and Pinion transmission, Linear Square orbit (Taiwan Hiwin).
Z - Movement
Imported ball screw made in Germany Linear Square orbit (Taiwan HIWIN)
Resolution Working Accuracy Reposition Accuracy
0.01 mm
0.05 mm
Machine Bed Structure
Welded Steel tube structure
Bed Type
T Slot + Vacuum
Max. idling speed
50 m/min
Spindle Type
3.0, 6kw air cooled HSD Italy
Spindle speed
0-24000 rpm (0-18000 rpm for HSD spindle)
Working voltage
Three Phase 380V/50Hz
Inverter
Delta Taiwan
Drive Motors
Stepper
Max. Power (without spindle)
1850 Watts
Max. Working Speed
25m/min
Command
G code, HPGL, U00, mmg, plt
Operating system
DSP
Interface
USB
Diameter of cutter
¦Õ3.175-¦Õ12.7
Dust collector (complete)
Yes
Work-holding
T Slot + By suction (vacuum)
Features:
1 The machine is welded with square steel tube, which has excellent stability and long life.
2 X and Y axis adopt rack and pinion transmission.Dust prooof structure on X axis.
3 Z axis adopts ball screw transimission.
4 Lubrication system on rails.
5 Software compatability: CAD/DAM design software eg. Type3/CorelDraw/Artcam/Castmate,etc. It can run on Windows XP/2000,32bits.
6 It has function of recarving/resuming after tool breakage, temporary pause and power failure. It has Memery to capture processing point. (DSP can capture 6 this break point when the tool or blade is broken or insituation of postponement, or of power failure.(only DSP can resume from power failure)
7 It has intelligent protection for working table to prevent damage. Our solution is to put a 5 mm MDF board on top of T-slot&vacuum table.
8 It has function of forecasting processing time.
9 It adopts advanced DSP system, with USB interface, for convenient ooperation. The engraver is capable of working completely off-line without any computer resources. Flas Memery 128 MB.
10 It has an independent control box.
11 Vacuum table with enough vacuum zones, which can hold different size of material. It is also very convenient to fix the material by clamp.
Function:
This machine is widely used in many industries such as: furnature, decoration, wooden doors, stone,metal....It is suitable to process various wooden products, nameplate, handicraft, graveston,
embossing, advertisement signboards, MDF, hard plastic, archaized furniture, arcrylic cutting, curved surface musical instrument, sucktion mould making, and other metallic or nonmetallic material....
Wood engraving CNC Router XYZ1325
XYZ1325 CNC Router
1 Italy HSD Air-cooled spindle
2 HIWIN rail guide
3 Vacuum Table/Dust collector/Automatic-mist spray
XYZ 1325 Wood Working CNC Router
Description
Parameter
X, Y, Z working area
1300 X 2500 X 200 mm
X, Y Movement
Rack and Pinion transmission, Linear Square orbit (Taiwan Hiwin).
Z - Movement
Imported ball screw made in Germany Linear Square orbit (Taiwan HIWIN)
Resolution Working Accuracy Reposition Accuracy
0.01 mm
0.05 mm
Machine Bed Structure
Welded Steel tube structure
Bed Type
T Slot + Vacuum
Max. idling speed
50 m/min
Spindle Type
3.0, 6kw air cooled HSD Italy
Spindle speed
0-24000 rpm (0-18000 rpm for HSD spindle)
Working voltage
Three Phase 380V/50Hz
Inverter
Delta Taiwan
Drive Motors
Stepper
Max. Power (without spindle)
1850 Watts
Max. Working Speed
25m/min
Command
G code, HPGL, U00, mmg, plt
Operating system
DSP
Interface
USB
Diameter of cutter
¦Õ3.175-¦Õ12.7
Dust collector (complete)
Yes
Work-holding
T Slot + By suction (vacuum)
Features:
1 The machine is welded with square steel tube, which has excellent stability and long life.
2 X and Y axis adopt rack and pinion transmission.Dust prooof structure on X axis.
3 Z axis adopts ball screw transimission.
4 Lubrication system on rails.
5 Software compatability: CAD/DAM design software eg. Type3/CorelDraw/Artcam/Castmate,etc. It can run on Windows XP/2000,32bits.
6 It has function of recarving/resuming after tool breakage, temporary pause and power failure. It has Memery to capture processing point. (DSP can capture 6 this break point when the tool or blade is broken or insituation of postponement, or of power failure.(only DSP can resume from power failure)
7 It has intelligent protection for working table to prevent damage. Our solution is to put a 5 mm MDF board on top of T-slot&vacuum table.
8 It has function of forecasting processing time.
9 It adopts advanced DSP system, with USB interface, for convenient ooperation. The engraver is capable of working completely off-line without any computer resources. Flas Memery 128 MB.
10 It has an independent control box.
11 Vacuum table with enough vacuum zones, which can hold different size of material. It is also very convenient to fix the material by clamp.
Function:
This machine is widely used in many industries such as: furnature, decoration, wooden doors, stone,metal....It is suitable to process various wooden products, nameplate, handicraft, graveston,
embossing, advertisement signboards, MDF, hard plastic, archaized furniture, arcrylic cutting, curved surface musical instrument, sucktion mould making, and other metallic or nonmetallic material....
1 Italy HSD Air-cooled spindle
2 HIWIN rail guide
3 Vacuum Table/Dust collector/Automatic-mist spray
XYZ 1325 Wood Working CNC Router
Description
Parameter
X, Y, Z working area
1300 X 2500 X 200 mm
X, Y Movement
Rack and Pinion transmission, Linear Square orbit (Taiwan Hiwin).
Z - Movement
Imported ball screw made in Germany Linear Square orbit (Taiwan HIWIN)
Resolution Working Accuracy Reposition Accuracy
0.01 mm
0.05 mm
Machine Bed Structure
Welded Steel tube structure
Bed Type
T Slot + Vacuum
Max. idling speed
50 m/min
Spindle Type
3.0, 6kw air cooled HSD Italy
Spindle speed
0-24000 rpm (0-18000 rpm for HSD spindle)
Working voltage
Three Phase 380V/50Hz
Inverter
Delta Taiwan
Drive Motors
Stepper
Max. Power (without spindle)
1850 Watts
Max. Working Speed
25m/min
Command
G code, HPGL, U00, mmg, plt
Operating system
DSP
Interface
USB
Diameter of cutter
¦Õ3.175-¦Õ12.7
Dust collector (complete)
Yes
Work-holding
T Slot + By suction (vacuum)
Features:
1 The machine is welded with square steel tube, which has excellent stability and long life.
2 X and Y axis adopt rack and pinion transmission.Dust prooof structure on X axis.
3 Z axis adopts ball screw transimission.
4 Lubrication system on rails.
5 Software compatability: CAD/DAM design software eg. Type3/CorelDraw/Artcam/Castmate,etc. It can run on Windows XP/2000,32bits.
6 It has function of recarving/resuming after tool breakage, temporary pause and power failure. It has Memery to capture processing point. (DSP can capture 6 this break point when the tool or blade is broken or insituation of postponement, or of power failure.(only DSP can resume from power failure)
7 It has intelligent protection for working table to prevent damage. Our solution is to put a 5 mm MDF board on top of T-slot&vacuum table.
8 It has function of forecasting processing time.
9 It adopts advanced DSP system, with USB interface, for convenient ooperation. The engraver is capable of working completely off-line without any computer resources. Flas Memery 128 MB.
10 It has an independent control box.
11 Vacuum table with enough vacuum zones, which can hold different size of material. It is also very convenient to fix the material by clamp.
Function:
This machine is widely used in many industries such as: furnature, decoration, wooden doors, stone,metal....It is suitable to process various wooden products, nameplate, handicraft, graveston,
embossing, advertisement signboards, MDF, hard plastic, archaized furniture, arcrylic cutting, curved surface musical instrument, sucktion mould making, and other metallic or nonmetallic material....
Subscribe to:
Posts (Atom)